Push Video MEGAPIXEL WIRELESS NETWORK CAMERA SERIES Dokumentacja Strona 1

n812_813_network_V1.3 1.3 MEGAPIXEL WIRELESS NETWORK CAMERA SERIES ADVANCED NETWORK SETUP Please read instructions thoroughly before operation and r

10 e) Wait for iPhone / iPad to search available wireless networks, and select the one you want to connect this camera to. f) Enter the key to join

11 f) Select “Config.”, and go to “Network”  “Wireless”. g) Click “Scan” to search all available wireless access points / routers (SSID), and doubl

12 1.4 Connect Camera to the Internet (WAN) You may use your laptop / computer, or your iPhone / iPad / Android mobile device to complete the network

13 Step3: Open Internet Explorer on your laptop / computer, and enter the IP address and port number you just found in the URL column to access this

14 Step6: Go to “UPnP”, and enable the UPnP service. Then, enable “Port Mapping”, and click “Save” to start port mapping automatically. When the

15 1.4.2 Configure on iPhone / iPad Before configuring this camera on iPhone / iPad, make sure:  You have installed our mobile program, EagleEyes-L

16 Step3: Select the IP address you want to configure to show the IP address setting page. Then, switch to the tab “Static”. The default port num

17 Check your connection Step1: Check if the LAN ( ) and Internet ( ) status indicators on the camera are always on.  If they’re both always on (

18 Connect a camera to the Internet Step1: Connect your Android device to the same wireless network (SSID) as the camera connected. Step2: Open “Ea

19 Step5: In the new device page, give a meaningful name for this connection in “Title”, and click “Save”. Step6: Go to “Check your connection” below

IMPORTANT SAFEGUARD All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous

20 1.5.2 From iPhone / iPad Log into the camera, and click “ ” on the top right corner to enter the system configuration page. Scroll down the page

21 2. BEFORE YOU START TO USE After you finish network configurations, some camera configurations in “Config.” are recommended to complete for the ca

22 APPENDIX 1 CHANGE IP ADDRESS OF YOUR LAPTOP / COMPUTER For LAN connection with this network camera, you need to change the IP address of your lapt

23 For Windows Vista users: a) Select “ ” (start)  “Control Panel”  “Network and Internet” to enter the “Network and Sharing Center”. Then, click “

24 b) Right-click on “Local Area Connection”, and select “Properties”. Note: If your local area connection is not enabled, please also enable it.

25 APPENDIX 2 NETWORK CONFIGURATIONS WITH ROUTER / MODEM If your network environment is “(Router + Modem”, “Wireless Router + Modem”, or “Modem” (or

26 Step3: Open Internet Explorer on your laptop / computer, and enter the IP address and port number you just set in the URL column to access this c

27 You can use the host name you noted down in Step5 to access your camera, such as MAC000e531d6ff1.ddns.eagleeyes.tw, or the IP address shown in St

28 Step2: Open “IPScan.exe” ( ) to search your camera. You will find two IP addresses:  192.168.2.10 - Please ignore this IP address.  192.168.30

29 Step5: Go to “Config.”  “DDNS”, and enable the DDNS service.  If your router supports UPnP, please proceed Step6.  If your router doesn’t

Disclaimer We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any legal liability or respo

30 Configure on iPhone / iPad Step1: Connect your iPhone to the wireless router as the camera connected. Step2: Open “EagleEyes” on your iPhone or

31 Step4: Select “Apply” to confirm all your changes. Then, wait till you see “Done” or “Fail” in “Status”. Regardless which message you see, proce

32 A2.3 Modem / Hub + Modem Before configuring the camera from your laptop / computer, make sure:  Your Windows operating system is Windows 7, Vist

33 Item Description Account Change your default account password if needed. This change can also be made in “Config.”  “General”  “Account”. Da

34 Step5: (Optional) Click “DDNS” ( ) to continue setting for PPPOE and DHCP. a) Enable DDNS. b) Select “eagleeyes” in “System Name”. c) In “Hostn

35 APPENDIX 3 MOBILE SURVEILLANCE VIA EAGLEEYES EagleEyes is a mobile phone program used with our surveillance system for remote surveillance. It has

36 APPENDIX 4 ENABLE PUSH VIDEO A4.1 What’s Push Video “Push Video” is an active notification system, different from traditional FTP & Email noti

37 A4.3.2 From Android Mobile Device In the address book, switch “Guard” from “OFF” to “ON”.

38 APPENDIX 5 CONFIGURE PORT FORWARDING You need to additionally access your router for port forwarding when your router doesn’t support UPnP. Each r

39 APPENDIX 6 ADDING WIRELESS PROFILE MANUALLY You can also add the wireless profile manually in the system configuration page from the web browser.

TABLE OF CONTENTS 1. NETWORK CONFIGURATIONS WITH WIRELESS ROUTER... 5 1.1 Assemble & Ins

40 APPENDIX 7 Q&A For more details about EagleEyes Q&A, please visit our official website: www.eagleeyescctv.com. Question Answer Does this

5 1. NETWORK CONFIGURATIONS WITH WIRELESS ROUTER You may configure the network connection of this network camera to Internet for remote surveillance

6 1.2 Prerequisites If your network environment is as illustrated below, make sure:  You know the password to join the network.  You’re sure yo

7 1.3.1 Connect to wireless routers with one press Note: The quick wireless connection setup function could be a virtual button on the wireless con

8 b) Open Internet Explorer, and enter “http://192.168.2.10:88” to access and log into the camera. Note: The default user name and password for log

9 h) Check the LAN status indicator ( ) on the camera, and see if it’s always on. - If yes, the camera is connected to the wireless network successf